November 16, 2020

Daewoo Washing Machine Error Codes

E9 This error occurs when the water level sensor frequency exceeds 30 kHz or below 15

KHz, as well as when the frequency suddenly increases by more than 1.44 kHz in

Four seconds after filling the water. The hose of the water level sensor is disconnected from the position. (This function will be applied later.

After a review in the future)

DE This error occurs if the door lock is not installed to open or close when the door lock

The solenoid works more than 10 times.

This error is cleared when the door is open.

LE This error indicates that the door opens while the washing machine is running.

The procedure for handling this error

Close the door, then the lock will turn on, and the course will continue

SE This error indicates that the safety switch is open right before entering the spin stage.

QE This error occurs when water does not drain more than 15 minutes.

IE This error occurs when the water level sensor frequency is no longer changing

Less than 0.08 kHz for 10 minutes after the beginning of filling with water, and also when water

Do not fill in within 60 minutes.

Daewoo Washing Machine Error Codes The procedure for handling this error

Open and close the door, check the water valve and water pressure and press

Start / Pause, then the error will be cleared and the water will be filled again.

UE This error occurs when the unbalance switch is activated for the third time after

Performing an unbalance operation (water pouring + flushing) twice during the spin stage.

The procedure for handling this error

Open the door, evenly distribute it and close the door. Then the error will be

Cleaning and rotation will be performed again

E5 (high DC voltage)

In the event that the DC voltage up to IPM increases to 450 V or higher

The engine stops and the display window shows “E5”.

The alarm sounds for 10 seconds every 10 minutes.

Error display is cleared when the power is turned off / on.

Error E6 (EMG)

In the event that the current detected by the EMG port is 20 A or higher

The engine stops and the display window shows “E6”.

The alarm sounds for 10 seconds every 10 minutes.

Error display is cleared when the power is turned off / on.

Error E7 (Direction)

In the event that the Hall signal IC differs from the predicted signal in accordance with the direction of rotation

The engine is stopped and “E7” is displayed in the display window.

The alarm sounds for 10 seconds every 10 minutes.

Error display is cleared when the power is turned off / on.

Error E8 (Error initial operation)

If the Hall input IC is abnormal due to problems with connecting the motor, etc.

The engine stops and the “E8” symbol is displayed in the display window.

The alarm sounds for 10 seconds every 10 minutes.

Error display is cleared when the power is turned off / on.

H2 Sensor for washing temperature open / short

In the event that the washing temperature sensor is defective or not connected

The alarm sounds for 10 seconds every 10 minutes.

Error display is cleared when the power is turned off / on.

H4 Overheating of the washing temperature sensor

In the event that the temperature detected by the flushing temperature sensor is 95 ° or higher

The alarm sounds for 10 seconds every 10 minutes.

Error display is cleared when the power is turned off / on.

H5 Water temperature error in wool / delicate course

If the water temperature in the wool / thin course is 45 ° or higher

The alarm sounds for 10 seconds every 10 minutes.

Error display is cleared when the power is turned off / on.

H6 Anomaly in the washer heater

15 minutes after the heater starts working;

If the standard temperature is 42 ° or lower: if the temperature does not increase by 2 ° or more

The standard case temperature is above 42 °: if the temperature does not increase by 1 or more

If the temperature falls below the standard temperature by 2 ° or more due to repeated water supply, etc.,

The standard temperature is reset when the current temperature and error check time are cleared within 15 minutes.

The alarm sounds for 10 seconds every 10 minutes.

Error display is cleared when the power is turned off / on.

Overheating of the H8 washer heater

In the event that the temperature of the washing heater increases by 5 ° or more for 30 seconds, when there is no

Water in a tank, etc.

The alarm sounds for 10 seconds every 10 minutes.

Error display is cleared when the power is turned off / on.

B1 Engine alignment error

This error occurs when the motor alignment at the initial

The engine running phase does not match the logic.

B2 Motor speed control

error

This error occurs when the difference between the current speed

And the target speed is more than 120 rpm.

B3 Low voltage error

This error occurs when the DC-LINK voltage is below 140 V

B4 Starting the engine

Overload error

This error occurs when the interior sensor input is missing

400 ms at engine start-up due to overload or engine blocking.

E1 Water level detection error

1) Conditions of occurrence

In case the water level is below zero or the overflow occurs in the line check mode

2) The water supply motor remains on until the water level drops below the reset.

3) All LEDs are off, and the “E1” indicator flashes on the display.

4) The alarm sounds for 10 seconds every 10 minutes.

5) The error indication is cleared when the power is turned off / on.

Error overflow E2

1) Conditions of occurrence

If the water level in the water tank has exceeded the level of overflow due to the continuous operation of the water supply

valve

2) The water supply motor remains on until the water level drops below the reset.

3) All LEDs are off, and the “E2” indicator flashes on the display.

4) The alarm sounds for 10 seconds every 10 minutes.

5) Error indication is cleared when power is turned off /

daewoo washing machine oe error code

The daewoo washing machine oe error code OE error code indicates that the washer is unable to use the water during the wash cycle. OE can be triggered by a drain drain hose or a closed drain pump filter.daewoo washing machine oe error code.

daewoo washing machine oe error code

MESSAGE	ERROR	CAUSE	SOLUTION
IE	WATER INLET ERROR	The water tap is closed.	Open the water tap.
		The filter of the valve inlet is clogged.	Clean the filter of the valve inlet.
		The valve inlet is an inferior product or broke down.	Change the valve inlet.
		The water level sensor (sensor pressure) is an inferior product or broke down.	Change the water level sensor (sensor pressure).
		The drain motor works during water supply.	Change the drain motor.
		The PCB ASS’Y does not check the water level.	Change the PCB ASS’Y.
OE	DRAIN ERROR	The drain hose is kinked or clogged.	Clean and straighten the drain hose.
		The drain motor is an inferior product.	Change the drain motor.
		The valve inlet works during drain.	Change the valve inlet
		The water level sensor is an inferior product.	Change the water level sensor.
		The PCB ASS’Y does not check the water level.	Change the PCB ASS’Y.
UE	UNBALANCE ERROR	The laundry is concentrated to one side of the drum during spin.	Rearrange the laundry.
LE	DOOR OPEN ERROR	The Start/Hold button is pressed while the door is opened.	Close the door.
		The switch door lock is an inferior product.	Change the switch door lock.
		The PCB ASS’Y does not check the door lock.	Change the PCB ASS’Y.
E2	OVERFLOW ERROR	The water is supplied continuously due to an inferior valve inlet.	Change the valve inlet.
		The valve inlet is normal, but the water level sensor (sensor pressure) is inferior.	Change the water level sensor (sensor pressure).
		The drain motor dose not work. (The drain motor is an inferior product or broke down.)	Change the drain motor.
E4	LEAKAGE ERROR	Water leaks from the tub or the hose drain.	Check the leak of the tub or the hose drain. Then change the tub or the hose drain.
E5	HIGH VOLTAGE ERROR	The laundry is jammed between the gasket and the drum.	Rearrange the laundry.
E5	HIGH VOLTAGE ERROR	The PCB ASS’Y is an inferior product.	Change the PCB ASS’Y.
E6	EMG ERROR	The laundry is jammed between the gasket and the drum.	Rearrange the laundry.
		The motor is an inferior product.	Change the motor.
		The PCB ASS’Y is an inferior product.	Change the PCB ASS’Y.
E8	MOTOR ERROR	The motor is not normally connected.	Check the connector of the motor.
E8	MOTOR ERROR	The motor does not work. (The motor is an inferior product or broke down.)	Change the motor.
E9	SENSOR PRES- SURE ERROR	The water level sensor is an inferior product.	Change the water level sensor.
H2	THERMISTOR WASH ERROR	The thermistor wash is an inferior product or broke down.	Change the thermistor wash.
H2	THERMISTOR WASH ERROR	The thermistor wash is not connected normally.	Check the connector of the thermistor wash.
H4	THERMISTOR WASH OVERHEATING ERROR	The heater worked without the water in the tub.	Check the water level.
H4	THERMISTOR WASH OVERHEATING ERROR	The thermistor wash is an inferior product or broke down.	Change the thermistor wash.
H5	WATER TEMP. ERROR	The water temp, is over 45°C in delicate & wool course. (The thermistor wash is an inferior product or broke down.)	Change the thermistor wash.
H6	HEATER WASH ERROR	The heater wash dose not work.	Change the heater wash.
H6	HEATER WASH ERROR	(The water temp, doesn’t rise over2°C during 15min.)
H8	HEATER WASH OVERHEATING ERROR	The heater worked without the water in the tub.	Check the water level and the heater wash.
lb	IGBT ERROR	The PCB ASS’Y is an inferior product.	Change the PCB ASS’Y.
PFE	PUMP FILTER ERROR	The drain pump filter is clogged.	Clean the drain pump filter.
		The drain pump does not work during spin.	Change the drain pump.
		The large amount of detergent was used.	Use the proper amount of detergent.
		The drain hose is placed higher than 1 m above the floor.	Place the drain hose 1 m below the floor