LG Dishwasher Error Code – How To Recognize And Repair Fault Codes In Your LG Dishwasher

Is there an error code on your LG dishwasher? If you have a newer LG dishwasher, the digital display may display error numbers. An error code is a message from your computer’s diagnostic system informing you that something is wrong. What is wrong with your dishwasher will be revealed by the precise problem code. It operates similarly to when a light illuminates on your car’s dashboard, alerting you to a potential problem. If you can identify the error number on your LG dishwasher, you can figure out how to solve the problem yourself. Usually, it’s only a matter of resetting things, but occasionally, the error number will indicate that a specific component is defective, clogged, or jammed. See the list below for a complete list of problem codes that your LG dishwasher may show…

How to Identify and Repair LG Dishwasher Error Codes

OE Error Code for LG Dishwasher:

The OE error number on your dishwasher’s display indicates that the appliance has detected a drain problem.

• This is frequently caused by blocked food or a problem with the installation.
• If there is water in the bottom of the dishwasher tub, choose a DRAIN ONLY option to drain the water.
• Look at the buttons on the display for a CANCEL & DRAIN under two buttons to finish a
• DRAIN DOWN BELOW TWO BUTTONS
• To initiate the CANCEL & DRAIN cycle, press the two buttons at the same time. (See illustration below.)

Display panel for LG dishwasher

If your dishwasher does not include a CANCEL & DRAIN option, simply start a cycle, wait 45 seconds, and then turn it off. The first 45 seconds of an LG dishwasher’s wash cycle are spent emptying.
This should get rid of the OE error code. If this is not the case, your LG dishwasher may need to be serviced.

OE Error Code for LG Dishwasher:

LG Dishwasher LE Error Code:

The LE error code on the dishwasher display indicates that the motor is not operating properly.
The following procedures can be taken to resolve the LE error code…

• Turn off the dishwasher by pressing the power button.
• Unplug the dishwasher or turn off the circuit breaker for 10 to 15 seconds.
• Reconnect the dishwasher or reset the circuit breaker.
• To start the dishwasher, press the power button.
• Begin a fresh cycle and check if the issue is resolved.

This should resolve the LE error code.

Error Code LE on LG Dishwasher

Error Code for LG Dishwasher HE:
Your LG dishwasher’s HE fault number indicates that it has detected a heating or heater problem.
This can occur if the dishwasher is unable to heat the water or if the water is too hot.
Here’s how to get rid of the HE error code…

• Turn off your dishwasher by pressing the power button.
• For 10 seconds, unplug the dishwasher.
•  Reconnect the dishwasher.
• Press the power button to turn it on.
• Begin a fresh wash cycle.

The HE error code should now be fixed.

LG Dishwasher FE Error Code:

If your dishwasher displays a FE fault code, it signifies that there is a water fill error.
The dishwasher has detected that there is too much water in the unit, and the drain pump has been activated.
This is generally cleared by following the instructions below…

• Turn off the dishwasher by pressing the power button.
• For 10 seconds, unplug the dishwasher.
• Reconnect the dishwasher.
• To restart the dishwasher, press the POWER button.
•  Begin a fresh wash cycle.

The FE error code should now be fixed.

Error code FE on LG dishwasher

CE Error Code on LG Dishwasher:

A CE error code on your dishwasher’s display indicates a problem with the motor’s operation.
Following these procedures should generally solve the problem…

• Turn off the dishwasher by pressing the power button.
• Turn off the dishwasher and wait 10 seconds before turning it back on.
• Reconnect the dishwasher.
• To start the dishwasher, press the POWER button.
• Begin a fresh wash cycle.

The CE error code should now be gone.

LG Dishwasher E1 Error Code:

An E1 error code indicates that the device may have a leak.
These leaks are caused by incorrect dishwasher installation, using the wrong detergent, or loading the dishes incorrectly.
To resolve this issue…

• Make sure the drain pipe is in good working order.
• Unwanted draining may occur if the drain hose outlet is set lower than the base of your LG dishwasher.
• If the drain hose is lower than the base, an E1 error may occur.
• Look for a syphoning issue in the drain pipe.
• To minimise water being sucked out of the tub, the drain hose end must be higher than 10″ from the dishwasher’s bottom.
• Look for fractures or damage in your drain hose that might cause water to escape.
• If the foregoing problems persist, replace the dishwasher drain hose.

PF Error Code on LG Dishwasher:

The PF error code on your LG dishwasher indicates a power loss.

• This function protects your dishwasher in the event of a power outage.
• To clear the display, press and hold any button on your dishwasher controls for 10 seconds after power is restored.
• When the PF warning shows repeatedly on your dishwasher and no power loss has occurred, it might be due to a circuit breaker that is unable to manage the dishwasher’s electrical requirements.
• A dedicated circuit breaker is required to power the dishwasher.

PF fault code on LG dishwasher

tE Error Code on LG Dishwasher:

A tE problem code on your dishwasher’s display indicates a thermal error.

• If the water temperature exceeds 194 degrees Fahrenheit, something occurs. This error number can also occur if the thermistor is malfunctioning.
• The tE error number usually indicates that your dishwasher need a new thermistor.

Error Code tE On LG Dishwasher

LG Dishwasher IE Error Code:

An iE or 1E error code on the display indicates a problem with the water level or the intake.
The dishwasher isn’t getting enough water.
The water level in your LG dishwasher did not grow high enough after filling for 10 minutes, according to an IE error code.
To resolve this issue…

• Double-check that the water supply valve is open.
• Check the water supply line for any bends, kinks, or clogs.
• Disconnect the dishwasher’s water supply line and test the flow of water in a bucket or similar container.
• If the washer continues to malfunction, replace the water intake valve.

IE ERROR CODE: IE DISPLAYED OR 1E DISPLAYED: INLET ERROR = INLET ERROR: Normal Water Level Not Reached Following 10 Minutes Of Water Supply Turned On

YOU MAY ALSO WATCH THIS VIDEO:

Error Codes and Problems with LG Dishwashers

YOU MAY ALSO READ THIS:

• LG Tower AC Error Codes|LG Cassette AC Error Codes | Inverter Type
• lg freezer not freezing | LG Refrigerator Working
• LG Split System Air Conditioner Error Code Troubleshooting – Maintenance
• Dishwasher leaking water | How to repair?
• LG AC Error Code Solution|Inverter Air Conditioner
• Baxi Gas Boiler Error Codes

Ballu Air Conditioner Error Code

Ballu air conditioner error code Ballu Air Conditioner Error Code Ballu air conditioner error code,MFS2 series E1, E2, E3, E4 - Temperature sensor (internal or external unit, condenser temperature, evaporator temperature) is small or broken. E6 - External unit safety tripped E8 - Closed Electrostatic Filter P4 - Error on ...
Read More

AmeriCool Air Conditioner Error Codes

AmeriCool Air Conditioner Error Codes AmeriCool Inc., a major manufacturer of portable air conditioners, is introducing a new product from a range of small commercial air conditioners WMC-2500 Since April 2013, the California company has released five new portable air conditioning devices. AmeriCool Inc. introduced even more innovative air conditioning ...
Read More

Amana Washing Machine Error Code

Amana Washing Machine Error Code Amana Washing Machine Error Code The history of the Aamna brand dates back to 1934. It was named after the place it was founded (Middle Amana, Iowa). Today, it manufactures an array of home appliances, including products for kitchens, laundry and heating. The list of ...
Read More

AMANA Air Conditioner Error Codes

AMANA Air Conditioner Error Codes AMANA Air Conditioner Error Codes CODE = FP Mode Status = Freeze Protection Attached. Room temperature is measured by a wireless remote thermostat or indoor ambient thermistor activated sensor Falls below 40 ° F. Display = y Error light = n Necessary action = No ...
Read More

Acson Air Conditioner Error Codes

Acson Air Conditioner Error Codes Acson Air Conditioner Error Codes A1 Indoor PCB ERROR A3 Drone Pump ABNORMAL A5 ANTIFREEZE (cooling) / heat accelerator overheating (heating) A6 Indoor Fan Motor Atal AH Electrical AIR Cleaners AB C4 INDOOR HEAT EXCHANGER (1) THERMISTOR SHORT / OPEN C5 INDOOR HEAT EXCHANGER (2) ...
Read More

Aeronik Air Conditioner Error Codes

Aeronik Air Conditioner Error Codes Aeronik Air Conditioner Error Codes Aeronic air conditioners not only provide heating or cooling Air in a residence or office. They make a favorable microclimate Inside the house taking care of the well being of a person. These air conditioners are long Time-tested, high level of utility. Aeronic ...
Read More

Aerotek Air Conditioner Error Codes

Aerotek Air Conditioner Error Codes Aerotek Air Conditioner Error Codes Aerotech produces climate equipment that does not The modern world is inferior to analogs and has fairly reasonable prices.All products are distinguished by the optimal "price-quality" ratio. forAir conditioners of this brand are used to produce components High quality only. Therefore, for ...
Read More

AKAI Air Conditioner Error Codes

AKAI Air Conditioner Error Codes This Akai air conditioner is equipped with a self-diagnosis (Error Codes) function to help you identify potential Issuess. Should you face Issuess with your air conditioner,  Contact our sales support center using the description at the bottom of the page. However, before calling for service, ...
Read More