Rheem AC Error Codes
Rheem AC Error Codes
Rheem AC Error Codes
Display Codes 0– standby
Diagnostic Description No command for unit operation
Possible Cause normal operation
Display Codes c – first stage
Diagnostic Description The cooling unit has received a command for first stage cooling
Possible Cause normal operation
Display Codes c flashing
Diagnostic Description Anti-short cycle timer (3 min.) or minimum run timer (30 sec) active
Possible Cause
• The unit has received a command for first stage cooling during an active anti-short cycle timer or a minimum run timer.
• Wait until the unit timer expires or press the test button to defeat the short cycle delay.
Display Codes C – Second stage coolant
Diagnostic Description The unit has got command for second stage cooling
Possible Cause normal operation
Display Codes C flashing
Diagnostic Description Anti-short cycle timer (3 min.) or minimum run timer (30 sec) active
Possible Cause
• During an active anti-short cycle timer or minimum run timer, the unit has received a command for second stage cooling.
• Wait unit timer has expired or press test button to defeat short cycle delay.
Display Codes H – First stage heat pump
Diagnostic Description The unit has received a command for the first stage heat pump
Possible Cause normal operation
Display Codes H flash
Diagnostic Description Anti-short cycle timer (3 min.) or minimum run timer (30 sec) action
Possible Cause
• The unit has received a command for active anti-short cycle timer or first stage heat pump during minimum run time
• Wait unit timer has expired or press test button to defeat short cycle delay
Display Codes H – Second Stage Heat Pum
Diagnostic Description The unit has received command for second stage heat pump
Possible Cause normal operation
Display Codes H flashing
Diagnostic Description Anti-short cycle timer (3 min.) or minimum run timer (30 sec) active
Possible Cause
• During an active anti-short cycle timer or minimum run timer, the unit has received a command for a second stage heat pump.
• Wait unit timer has expired or press test button to defeat short cycle delay
Display Codes D – Defrost Active
Diagnostic Description The A/C is going through a defrost cycle
Possible Cause normal operation
Display Codes t – test mod
Diagnostic Description Test mod
Possible Cause ICC is in test mode
Display Codes P-Guard Trip
Diagnostic Description A command exists for compressor operation but no current is measured for the compressor
Possible Cause
Motor protector open
Display Codes 01 – Long Run Time (Compressor)
Diagnostic Description In mode cooling the compressor has run continuously for more than 18 hours.
Possible Cause
• low refrigerant charge
• There is enough leakage in the air ducts
• dirty indoor air filter
• dirty outdoor coil
Display Codes 02 – High Pressure
Diagnostic Description The compressor limit is opened four (4) times within a call to operation.
Possible Cause
• External coils are dirty ( mode cooling)
• Outdoor fan is not running (mode cooling )
• Dirty indoor coil or filter (mode heating )
• Indoor blower is not running (mode heating )
• liquid line restrictions
• excessive refrigerant charge
Display Codes 03 – Short Cycling
Diagnostic Description The ICC detects the run time for the last four (4) compressors or cycles that are less than three (3) min. each
Possible Cause
• Check the thermostat wire connection
• Check thermostat location in the zone
Display Codes L4 – Lock Rotor
Diagnostic Description ICC four (4) detects that there have been frequent guard trips and the average run time for each trip is less than 15 sec
Possible Cause
• bad run capacitor
• low line voltage
• excessive refrigerant in the compressor
• Seized Bearings in Compressor
Display Codes 05 – Open circuit (compressor will not runing)
Diagnostic Description ICC has traveled a guard for more than 4 hours
Possible Cause
• Check for damaged, incorrect, or incorrect run capacitors
• Check for broken wires, loose connectors, or incorrect compressors
• Check the compressor winding for continuity
• Check for open compressor internal protector
Display Codes 06 – Compressor Open Start Circuit
Diagnostic Description ICC detects current in run circuit but not in start circuit of compressor
Possible Cause
• Check for damaged, incorrect, or incorrect run capacitors
• Check for broken wires, loose connectors, or incorrect compressors
• Check the compressor winding for continuity
Display Codes L6 – Compressor Open Start Circuit
Diagnostic Description ICC detects current in the run circuit but not in the start circuit of the compressor four (4) times in a compressor call
Possible Cause
• Check for damaged, incorrect, or incorrect run capacitors
• Check for broken wires, loose connectors, or incorrect compressors
• Check the compressor winding for continuity
Display Codes 07 – Compressor Open Run Circuit
Diagnostic Description ICC detects current in start circuit but not in run circuit of compressor
Possible Cause
• Check for damaged, incorrect, or incorrect run capacitors
• Check for broken wires, loose connectors, or incorrect compressors
• Check the compressor winding for continuity
Display Codes L7 – Compressor Open Run Circuit
Diagnostic Description The ICC detects the current in the start circuit but not four (4) times in a compressor call in the compressor’s run circuit
Possible Cause
• Check for damaged, incorrect, or incorrect run capacitors
• Check for broken wires, loose connectors, or incorrect compressors
• Check the compressor winding for continuity
Display Codes 09 – Low Secondary Voltage
Diagnostic Description Secondary voltage at R and C is below 18VoltAC
Possible Cause
• control transformer overload
• low line voltage
Display Codes 21 – Low Pressure Control Open
Diagnostic Description ICC LPC detects open. Note: Low pressure control is ignored for the first 90 sec of compressor operation
Possible Cause
• Refrigerant charge in the unit is low
• Indoor coil is frozen (mode cooling)
• Dirty indoor coil or filter (mode cooling)
• Indoor blower is not running(mode cooling)
• External (outdoor)coil is frozen (heating mode)
• Expansion valve is not working correctly
Display Codes L21 flashing
Diagnostic Description Active Safety, Low Pressure Control Trip
Possible Cause
LPC has opened 3 times in the same cooling operation, ICC has locked the compressor to protect it. The ICC alternately flashes L and 21.
Display Codes 27-
Diagnostic Description low voltage or no voltage Error
Possible Cause
• Disconnect and check the incoming line voltage for the unit
• Check the wiring connection
Display Codes 28
Diagnostic Description High line voltage
Possible Cause
Fault check line voltage
Display Codes 29
Diagnostic Description High Pressure Control Open. ICC discovers that HPC is open
Possible Cause
• External coils are dirty (mode cooling)
• Outdoor fan is not running (mode cooling)
• Dirty indoor coil or filter (mode heating)
• Indoor blower is not running (mode heating)
• liquid line restrictions
• excessive refrigerant charge
Display Codes L29 Flashing – Active Protection
Diagnostic Description High pressure control trip
Possible Cause
LPC has opened 3 times in the same cooling operation, ICC has locked the compressor to protect it. ICC alternately flashes L and 29
Display Codes 30 – Fuse Open
Diagnostic Description ICC discovers that on-board fuse is open
Possible Cause
• 3-amp fuse on ICC is open.
• Low voltage wiring on R and C is damaged or incorrect.
Display Codes 80 –
Diagnostic Description Low Airflow
Possible Cause
The ICC detects that the indoor unit is not providing minimum airflow requirements.
Misapplied wrong indoor air mover – replace with properly sized machine.
Display Codes 83 – Condenser Coil Temperature Defect
Diagnostic Description The sensor detects abnormally low or high coil temperatures
Possible Cause
• replace the sensor
• Check sensor control is installed correctly
Display Codes 84 – Outdoor Ambient Temperature Defects
Diagnostic Description The sensor detects abnormally low or high outdoor ambient temperatures
Possible Cause
• Check unit placement – If the outdoor unit is in a high temperature area, wait until the ambient temperature decreases and check the sensor readings.
• Replace the sensor.
• Check sensor control is installed correctly
Display Codes 93 – Internal Control Defect
Diagnostic Description Control is not working properly.
Possible Cause
• Check the controls for proper system operation.
• change control
Display Codes d1
Diagnostic Description N0 shared data
Possible Cause
Replace the memory card with the correct system information.
Display Codes D3 – Airflow CFM Mismatch
Diagnostic Description Indoor air movers (air handlers / furnaces) cannot supply the airflow required for proper system operation
Possible Cause
Misplaced indoor air mower-replacement with incorrectly sized air handler / furnace.
Display Codes d4 – (device) memory card invalid for device
Diagnostic Description The data in the memory card inserted into the control board does not match the data in the control.
Possible Cause
• Check the memory card to make sure it matches the device
• Check if a memory card is present
Display Codes d8 – old shared data
Diagnostic Description System data is obsolete
Possible Cause If the system will not operate, order a new memory card to update the system information.
Reem AC ICC Diagnostic Codes
The details of ICC diagnosis code are given below:
Note: Code should be read from the right side to avoid error in reading the code.
Rheem AC Error Codes Troubleshooting
Rheem AC Error Codes
Rheem AC Error Codes Disconnect all power to the unit before servicing. The contactor can break only one side. Failure to turn off the power can result in an electric shock resulting in personal injury or death.
SYMPTOM: Unit will not run
Possible reasons:
1. Power off or loose electrical connection
2. Thermostat set in too low – set too high
3. Defective control board
4. Blown fuses / tripped breaker
5. Transformer Deform
6. High Pressure Control Open / Low Pressure Control Open
7. Misuse of communication
Diagnosis:
1. Check the correct voltage at the line voltage connection in the condensing unit.
2. Reset.
3. Check the control board diagnostic code.
4. Replace the fuse / reset breaker.
5. Check the wiring. Replace Transformer.
6. Reset. Also see high head pressure measures. Highpower control opens at 610 PSIG.
7. Check communication cables
Symbol: outdoor fan, compressor does not run
Possible reasons:
1. Run or start capacitor faulty
2. Defective contact
3. Loose connection
4. Compressor stuck, grounded or open motor winding, open internal overload.
5. Low voltage conditions
Diagnosis:
1. Change.
Change 2..
3. Check the correct voltage on the compressor. Check all connections and tighten them.
4. Wait at least 3 hours to reset the overload. If still open, replace compressor.
5. Add the Start Kit component.
Symptoms: insufficient cooling
Possible reasons:
1. Unreasonably sized unit
2. Improper indoor airflow
3. Wrong refrigerant charge
4. Humidity in air, noncondensibles, or systems
5. Bad ID TXV
Diagnosis:
1. Recalculate weights.
2. Investigation. Must be around 400 cfm per ton.
3. Charge per process associated with the unit service panel.
4. Recover refrigerant. Empty and recharge Add filter dryer.
5. Change TXV
Characteristics: compressor short cycle
Possible reasons:
1. Wrong voltage
2. Defective overload protector
3. Refrigerant undercharge
Diagnosis:
1. At the compressor terminals, the voltage ing should be of 10% nameplate marking when the unit is operating.
Change 2.. Check for correct voltage.
3. Add refrigerators.
Symptoms: registers sweating
Poseblish Cas: Low Indoor Airflow
Remedy: Increase the speed of the blower or decrease the restriction. Change air filter
Characteristics: high head, low vapor pressure
Possible reasons:
1. The liquid line has expansion, expansion device, or filter drier
2. Bad TXV
Diagnosis:
1. Remove or replace the defective component.
2. Change TXV
Characteristics: high head, high or normal vapor pressure – cooling mode
Possible reasons:
1. dirty outdoor coil
2. Refrigerant overcharge
3. Outdoor fan not running
4. In air or noncondensible systems
Diagnosis:
1. Clean coil.
2. Correct system charge.
3. Repaired or replaced.
4. Recover refrigerant. Empty and recharge
Characteristics: low head, high vapor pressure
Possible reasons:
1. Bad TXV
2. bad compressor
Diagnosis:
1. Change the TXV.
2. Replace the compressor
SYMPTOM: Low Vapor, Quiet Compressor, Iced Indoor Coil
Possible reasons:
1. Low indoor airflow
2. Outside operating below 65 ° F
3. Moisture in the system
4. Closed ID Circuit
Diagnosis:
1. Increase the speed of the blower or reduce the restriction. Replace the air filter.
2. Add a low ambient kit.
3. Recover refrigerant. Empty and recharge Add filter dryer.
4. Repair or replace ID coil
Characteristics: high vapor pressure
Possible reasons:
1. Excess weight
2. Defective compressor
Diagnosis:
1. Check the load count again.
Change 2..
Symbol: fluctuating head and vapor pressure
Possible reasons:
1. TXV Hunting
2. In air or noncondensible systems
Diagnosis:
1. Check the TXV bulb clamp. Check air distribution on the coil. Replace TXV.
2. Recover refrigerant. Empty and recharge
Characteristics: noise or pulsing noise on the expansion device or liquid line
Poseblue CAS: In air or noncondensible systems
Remember: recover chill. Empty and recharge
Rheem AC Error Codes
Rheem AC Error Codes
About Author
I’ve been browsing online more than three hours today, yet I
never found any interesting article like yours. It is pretty worth enough for me.
In my opinion, if all web owners and bloggers made good content as
you did, the net will be much more useful than ever before.
Have you ever considered writing an ebook or guest authoring on other
websites? I have a blog based on the same topics you discuss and would really like to have you share some stories/information. I know my
visitors would appreciate your work. If you are even remotely interested, feel free to
shoot me an email.
I have fun with, cause I found just what I was having a look for. You have ended my 4 day long hunt! God Bless you man. Have a great day. Bye
Hello.This post was really remarkable, especially since I was searching for thoughts on this matter last Wednesday.
Hey very cool web site!! Man .. Excellent .. Amazing .. I’ll bookmark your blog and take the feeds also…I am happy to find numerous useful info here in the post, we need work out more techniques in this regard, thanks for sharing. . . . . .
you have got a terrific blog right here! would you wish to make some invite posts on my blog?
Nice post. I be taught one thing tougher on completely different blogs everyday. It will all the time be stimulating to read content material from different writers and follow a little bit one thing from their store. I’d favor to use some with the content material on my weblog whether you don’t mind. Natually I’ll give you a hyperlink on your net blog. Thanks for sharing.
Very nice post. I just stumbled upon your blog and wanted to say that I have really enjoyed surfing around your blog posts. After all I will be subscribing to your feed and I hope you write again very soon!