Sanyo Air Conditioner Error Codes | Inverter
Sanyo Air Conditioner Error Codes
Sanyo AC Error Codes
Sanyo AC Error Codes Diagnostics Item
S01 room Temp. sensor failure
S02 indoor heat exchanger sensor failure
S03 humidity sensor failure
S04 Compressor Temp. Sensor Failure
S05 outdoor heat exchanger sensor failure
S06 outdoor air Temp. sensor failure
S07 to detect outdoor electric current
E01 lndoor / outdoor communication failure
E02 • HIC circuit failure
• Power tr (transistor) circuit failure
E03 outdoor unit external ROM (OTP data) failure
E04 peak current cut off
E05 • PAM circuit failure
• active circuit failure
E06 Compressor Discharge Overheat Prevention Active
E07 Indoor fan operating failure
E08 • 4-way valve switching failure
• indoor zero-cross failure
E09 No-Reincarnation Protection
E10 DC Compressor Drive Circuit Failure
E11 outdoor fan operating failure
E12 • outdoor system communication failure
• OLR operation
• outdoor power supply open phase
• outer coil cold
E13 active freeze-prevention operation
Sanyo fault code and probable cause malfunction
Sanyo AC Error Codes
Fault (Error) code causing possible malfunction
E01 serial comms detecting Fault (Error), miss-setting, Fault (Error) signal from RC IU, outdoor system address, indoor system address.
E02 serial comms Fault (Error), wrong setting, detecting Fault (Error) signal from RC IU, Fault (Error) transmitting serial com signal
E03 IU detecting Fault (Error) signal from remote controller (and system controller)
E04 is detecting a signal Fault (Error) from IU OU, which is an Fault (Error) in receiving serial comms signal
E05 is detecting an Fault (Error) signal from an IU OU, which is an Fault (Error) in transmitting serial comms signals
E06 OU is detecting a signal Fault (Error) from IU, Fault (Error) in receiving serial comms signal (inc unit volume verification failure)
E07 OU detecting a signal Fault (Error) from IU, Fault (Error) transmitting serial comms signal
Improper setting of E08 IU or RC, IU address is duplicate
Improper setting of E09 IU or RC, remote controller setting is duplicate
E10 IU detecting signal Fault (Error) from signal option, Fault (Error) transmitting serial comms signal
E11 is detecting a signal Fault (Error) from the IU signal option, which is an Fault (Error) receiving a comms signal
The E12 IU is detecting a signal Fault (Error) from the signal option, as the auto address setting is in process in a different system.
E14 setting Fault (Error), main unit duplication in simultaneous-operation multi-control (detected by external unit)
E15 automatic address setting failed, IU capacity too low
E16 automatic address setting failed, IU capability too high
E17 One IU detected Trouble with signal from another IU, Fault (Error) in transmitting serial coms signal
E18 One IU detects signal Trouble from other IU, Fault (Error) in receiving serial comms signal
E20 automatic address setting failed, no other IU received signal
E24 auto address Fault (Error), detecting Fault (Error) signal from main OU sub OU
E25 auto address Fault (Error), OU address setting
E26 auto address Fault (Error), number of connected mains and sub OUs do not correspond to number set on main OU PCB
E29 auto address Fault (Error), sub OU receiving serial low signal from main OU
F01 thermistor faults, indoor coil temp. Sensor (E1)
F02 thermistor faults, indoor coil temp. Sensor (E2)
F03 thermistor defect, indoor coil temp. Sensor (E3)
F04 Outdoor Thermistor Open Circuit, TD1 Discharge
F05 Outdoor Thermistor Open Circuit, TD2 Discharge
F06 Outdoor Thermistor Open Circuit, Heat Exchanger Temp. C1
F07 Outdoor Thermistor Open Circuit, Heat Exchanger Temp. C2
F08 Thermistor Fault, Outdoor Air Temp. Sensor (Air Temp)
F10 Thermistor Fault, Indoor Suction Air (Room) Temp Sensor (TA)
F11 Thermistor Fault, Indoor Discharge Air Temp. Sensor (BL)
F12 Outdoor Thermistor Open Circuit, Intake Temp. TS
F16 Thermistor Defect, Outdoor High Pressure Sensor
F17 Thermistor Fault, Outdoor Unit Low Pressure Sensor
F22 Thermistor Fault, Outdoor Unit Compressor 3 (Constant Speed) Discharge Temp Sensor
F23 Thermistor Fault, Outdoor No. 2 Coil Gas Temp (EXG2)
F24 thermistor faults, outdoor No. 2 coil liquid temp. Sensor (EXL2)
F25 thermistor faults, external unit heat exchanger 3 gas temp. The sensor
F26 thermistor faults, external unit heat exchanger 3 liquid temp. The sensor
F29 Indoor EEPROM Fault (Error)
F31 outdoor EEPROM Fault (Error)
H01 AC1 compressor protection, overload current was detected
H02 AC1 Compressor Protection, Lock Current Detected
H03 AC1 Compressor Protection, no current detected when the compressor was on (CT1 circuit failure)
H05 compressor discharge sensor is disconnected (detected only for AC1 compressor)
H16 Low Pressure Switch AC1, AC2 Activated on Compressor
H07 protective device for compressor is active, low oil level
H08 protective device for compressor is activated, compressor no. 1 oil sensor defect (disconnection, etc.)
H11 AC2 compressor protection, overload current was detected
H12 AC2 Compressor Security, lock current was detected
H13 AC2 Compressor Protection, no current detected when the compressor was on (CT2 circuit failure)
H15 AC2 compressor discharge sensor is disconnected
H21 outdoor protective device, overload current detected on compressor 3 (constant speed)
H22 outdoor protective device, current lock detected on compressor 3 (constant speed)
H23 outdoor protective device, no current detected when on compressor 3 (constant speed)
H25 Outdoor Protective Equipment, Discharge Temp. Sensor Trouble, compressor 3 (constant speed)
H27 protective device for compressor is activated, compressor no. 2 oil sensor faults (disconnection, etc.)
H28 connection failure of oil detection sensor, compressor number 3 (competitive speed)
H31 Outdoor Unit Protection IPM Travel (IPM Current or Temperature) HIC Alarm Trouble
L02 wrong setting error, IU / OU type mismatch
L03 Incorrect setting error, main unit duplication in group control (detected by IU)
L04 Incorrect setting error, OU address duplication (system address)
L05 is improper setting, 2 or more IU RCs that are operation mode priority in refrigeration circuits.
L06 is improper setting, 2 or more IU RCs that are operation mode priority in refrigeration circuits.
L07 wrong setting error, wiring group connected for independent IU
L08 Incorrect setting error, IU address set or group not set
L09 Incorrect setting error, IU capability not set
L10 wrong setting error, OU capability set or no error setting
L11 wrong setting error, misunderstanding in group control wiring
L13 wrong setting error, IU type setting error
L17 mismatch connections of external units that have a different type of refrigerant
L18 4-Way Valve Operation Failure
P01 Indoor Fan Protective Thermostat
P02 AC compressor or AC1, AC2 compressor internal protection thermostat was activated: or low voltage was detected
P03 discharge temperature Trouble on outdoor
Operating high pressure sensors on P04 AC, AC1 or AC2 compressors
P05 open phase detected, AC power problem
P09 Roof Panel Connection Failure
P10 Indoor Float Switch
P12 Indoor Fan Overload (check packaging on new CAS install)
Failure to run P16 compressor resulted in missing stage compressor wiring etc.
P17 Wrong discharge temperature (comp number 2)
P22 outdoor unit fan (missing phase in HALL IC or other problem) causing fan to lock
P26 overcrack runs more than 80hz at the time of the compressor (other than the DCCT secondary current or the ACCT primary current when the IPM has tripped
P29 inverter is unusual for compressor (DC compressor does not operate)
P31 a flexible control error occurred
Sanyo air conditioner Troubleshooting
Sanyo AC Error Codes,If your air conditioner does not work properly, check the following points before requesting service. If it still does not work properly, contact your dealer or service center.
1-Trouble
The air conditioner does not work at all.
Probable cause
1. Power failure.
2. Leakage breaker tripped.
3. The line voltage is too low.
4. The ON / OFF operation button is OFF.
5. There is a shortage of batteries in the remote control unit.
Solution
1. Restore power.
2. Contact Service Center.
3. Consult an electrician or dealer.
4. Press the button again.
5. Change the battery.
2-Trouble
Compressor runs but stops soon
Probable cause
1. Obstacle in front of condenser coil.
Solution
1. Remove the obstacle.
3-Trouble
Poor cooling performance.
Probable cause
1. Dirty or clogged air filter.
2. Heat source (cooker, heater, or electrical appliance) or several people in the room.
3. Doors and / or windows open.
4. Interruption near air intake or air discharge port.
5. Thermostat is set too high.
Solution
1. Clean the air filter to improve air flow.
2. Remove the heat source if possible.
3. Turn them off to keep the heat out.
4. Remove it to ensure good air flow.
5. Set the temperature to low.
4-Trouble
The operation lamp does not blink and the air conditioner does not operate.
Probable cause
System Trouble.
Solution
Contact the service center.
Sanyo Air Conditioner
5-Trouble
The clicking sound is heard from the air conditioner.
Probable cause
In a heating or cooling operation, any plastic parts may expand or shrink due to sudden temperature changes. In this event, a clicking sound may occur.
Solution
This is normal, and the sound will soon disappear.
6 – Trouble
The operating lamp lights but the external unit will not run.
Probable cause
The use of a cellular phone near the air conditioner may cause disturbances in its normal operation.
Solution
1. Turn off the power and then turn the air conditioner again after a while.
2. Consult your dealer.
Hitachi ac error code|Solution
About Author
