February 26, 2022

Whirlpool Oven Troubleshooting What To Look For

By intakhab Uncategorized, Whirlpool 0 Comments

Whirlpool Oven Troubleshooting What To Look For – How To Get Clear Of It

Whirlpool Oven Troubleshooting Whirlpool Stove Error Codes stoves, ranges, and ovens. Error codes appear on the display of your Whirlpool oven to alert you to a problem. This comprehensive list of Whirlpool oven error code meanings will aid you in determining the source of the problem. To clear, check, diagnose, and repair your oven, use the codes below. You’ll know which part of the oven is broken and creating the issue after you read the error code. After that, you can buy the part and repair the oven yourself. Whirlpool ovens have 3 letter error codes, 2 digit error codes, and 4 digit error codes. This implies that your Whirlpool oven will display either two sets of two digits with a letter and a number, or two sets of two digits with a letter and a number.e2 f3 is an example of a four-digit error code.

3 Letter Error Codes for Whirlpool Range, Stove, and Oven:

LOC is the Whirlpool Oven Error Code.

Error Code:- Reason Child LOCK is ON
To remove LOC from the display, press and hold the ‘Start’ or ‘Cancel’ button for ten seconds.

Error Code:- PSH Whirlpool Oven

If Start is not hit within 5 seconds, the error code “PUSH” or “PSH” shows on the display – press Start.

The function is aborted and the time is displayed if start is not pushed within one minute of pressing the keypad.
If you get a continual PSH error, check/troubleshoot = Reset the oven’s power:

Turn off the oven’s circuit breaker for one minute.
Turn on the oven circuit breaker.
After one minute, check the oven to make sure the error code has been cleared.

2 Digit Error Codes for Whirlpool Range, Stove, and Oven:

Error Code:- F0 If there have been no previous fault codes, press CANCEL to clear them.

Error Code:- F1 Defective Electronic Oven Control or EOC is the reason/condition for the error code.

Unplug the oven power cord or turn off the circuit breaker. If the F1 error persists, replace the EOC.
Electronic Oven Control = Replace/Check Parts (EOC)

Error Code:- F2 Oven Temperature Too High Reason/Condition for Error Code

Check/Troubleshoot On both the bake and broil relays, look for welded contacts.

Contact Relay – Control Board = Replace/Check Parts

Error Code:- F3 Open Oven Temperature Sensor is the reason/condition for the error code.

Replace/Inspect Parts Oven Temperature Sensor Replacement

Error Code:- F4 Error’s Condition Shorted Oven Temperature Sensor

Replace/Inspect Parts Oven Temperature Sensor Replacement

Error Code:- F5 Control Board Fail is the reason for the error code.

Parts to be replaced Or check Control Board to be replaced

Error Code:- F7 Error Cause Function Key Is Stuck Code

Parts to be checked Control Board to be replaced

Error Code:- F8 Control Board Fail is the reason for the error code.

Parts to be checked Control Board to be replaced

Error Code:- F9 Oven Door Locking Fail is the reason for the error code.

Check/Troubleshoot Door lock switches, stuck lock switch, and wiring should all be checked.

Parts to replace/inspect Door Lock Switch

Oven Range Stove Parts Whirlpool

4 Digit Error Codes for Whirlpool Ranges, Stoves, and Ovens:

Error Code:- F2 E0 Error’s Cause Keypad Wiring Harness Code NOT IN CONNECTION

Unplug the oven power cord or switch off the circuit breaker to check/troubleshoot. Reconnect the electrical harness for the keypad. Replace the oven power cord or reset the circuit breaker. On the display, press CANCEL. If the problem code reappears after 1 minute, the keypad should be replaced. If the F2 E0 error continues, the electronic oven control should be replaced.

Keypad – Electronic Oven Control = Replace/Check Parts

Error Code:- F2 E5 CANCEL Key (Button) Is Faulty is the reason for Error Code

Unplug the oven power cord or switch off the circuit breaker to check/troubleshoot. Reconnect the electrical harness for the keypad. Replace the oven power cord or reset the circuit breaker. On the display, press CANCEL. If the problem code reappears after 1 minute, the keypad should be replaced. If the F2 E5 error continues, the electronic oven control should be replaced.

Keypad – Electronic Oven Control = Replace/Check Parts

Error Code:- F2 E6 CANCEL Key (Button) Is Faulty is the reason/condition for Error Code

Unplug the oven power cord or turn off the circuit to check/troubleshoot.

breaker. Reconnect the electrical harness for the keypad. Replace the oven power cord or reset the circuit breaker. On the display, press CANCEL. If the problem code reappears after 1 minute, the keypad should be replaced. If F2 E6 persists, the electronic oven control should be replaced.

Keypad – Electronic Oven Control = Replace/Check Parts

Error Code:- F3 E0 Open Oven Temp Sensor Circuit OR Faulty Oven Temp Sensor Reason for Error Code

Unplug the oven power cord or switch off the circuit breaker to check/troubleshoot. Reconnect the electrical harness for the oven temperature sensor. If the wire harness is shorted, it must be replaced. Check the resistance of the oven temperature sensor with an ohm metre. Replace the oven temperature sensor if the resistance is not 1080 ohms at room temperature. Replace the electronic oven control if the oven temp sensor resistance is good.

Oven Temperature Sensor – Wiring Harness – Electronic Oven Control = Replace/Check Parts

Error Code:- F3 E1 Oven Temp Sensor Faulty OR Shorted = Reason/Condition for Error Code Temperature Control in the Oven

Oven Temperature Sensor – Wiring Harness – Electronic Oven Control Replace/Check Parts

Error Code:- F3 E2 Oven Temp Over 575 Degrees In BAKE Mode = Reason/Condition for Error Code

Oven Temperature Sensor – Wiring Harness – Electronic Oven Control = Replace/Check Parts

Error Code:- F3 E3 Oven Temp TOO HIGH In CLEAN Mode is the reason/condition for Error Code.

Unplug the oven power cord or turn off the circuit to check/troubleshoot.

breaker. The oven temperature sensor wire should be reconnected. If the wire harness is shorted, it must be replaced. Using a volt/ohm metre, check the resistance of the oven temperature sensor. Replace the oven temperature sensor if the resistance is not 1080 ohms at room temperature. Replace the electronic oven control if the oven temperature sensor resistance and wire harness connections are OK.

Oven Temperature Sensor Wire Harness Electronic Oven Control Replace/Check Parts

Error Code:- F4 E1 Meat Probe Faulty/Shorted is the reason/condition for the error code.

Unplug the oven power cord or switch off the circuit breaker to check/troubleshoot. Measure the resistance of the meat probe with a volt/ohm metre. Replace the meat probe if the resistance is not 59000 ohms at room temperature. If the meat probe’s resistance is good, insert the probe and verify for a secure connection between the probe and the jack. If the jack is worn, it should be replaced. Make sure the meat probe jack’s wire harness isn’t loose. If necessary, replace the wire harness.

Meat Probe – Meat Probe Jack – Wire Harness = Replace/Check Parts

Error Code:- F5 E0 Door Open BUT Latch Is Locked – Latch Switch Communicates A Locked Door Reason/Condition for Error Code = Door Open BUT Latch Is Locked – Latch Switch Communicates A Locked Door

Examine the Troubleshooting By opening and closing the oven door, you may check the oven door switch. Examine the oven light to see if it turns on and off. Replace the oven door switch if it is broken. Turn off the circuit breaker or unplug the oven power cord. On the oven door lock assembly, connect any loose wire harnesses. If necessary, replace the wire harness. Check for flaws in the door lock assembly and repair it if necessary.

Oven Door Switch – Oven Door Locking Assembly – Wire Harness Replace/Check Parts

Error Code:- F5 E1 Self Clean Latch Will Not Lock or Unlock = Reason for Error Code

Unplug the oven power cord or switch off the circuit breaker to check/troubleshoot. On the oven door lock assembly wiring harness, reconnect any loose wires. If necessary, replace the wire harness. Check for flaws in the door lock assembly and repair it if necessary.

Oven Door Locking Assembly – Wire Harness = Replace/Check Parts

Error Code:- F5 E1 Whirlpool Oven Error

Error Code:- E1 F2 Whirlpool Oven Error

The parts listed below are for a Whirlpool Oven, Range, and Stove.
Due to erroneous codes, replacement parts are required.

YOU MAY ALSO READ THIS